If you’re wondering how to install kitchen cabinets, you’ve come to the right place. Here are a few simple steps to ensure your new kitchen cabinets fit perfectly. First, find the highest point of your floor and mark a horizontal positioning line. Then, shim the top of the base cabinet and place the end units a quarter inch away from the layout line.
Find your floor’s highest point
Before installing your kitchen cabinets, you should first find the highest point in the room. This will help you determine where the base cabinets should be installed. You can do this by drawing a level line all around the room, and then measuring every two feet. Once you have all the measurements, you can then determine the smallest measurement and install your cabinets accordingly.
The next step is to find the high point of your floor, which will act as your reference for the entire installation. If the floor is uneven, make sure to use a leveled line to keep the upper base cabinets level. This will ensure that you do not hit your head on the floor while you’re installing your cabinets.
Once you’ve measured the distance between the wall and the highest point of the floor, you can then place the base cabinets. The highest point will be the point closest to the wall. If you’re doing DIY installation, you’ll have to get a reference point. You’ll also need a level to measure the height of the base cabinets.
Mark the horizontal positioning line
After determining where the studs are in the wall, mark the horizontal positioning line on the wall. This line will indicate where the cabinets will sit when installed. It will also help you locate obstacles, such as ductwork or plumbing lines. Identifying these lines will make the installation process much easier.
Once you have marked the line, you can install the cabinets. Line up the bottom of the cabinet with the line you marked on the wall. Then, line up the pilot holes with the wall studs. Once the screws are in place, use a helping hand to hold the cabinet in place.
Once the cabinets are installed, make sure that the floor is level. If the floor isn’t level, make use of a spinning laser level to level the floor. Otherwise, a standard level and tape measure will work. The high point of the floor should be at least 34-1/2 inches off the floor.
Once you have measured the height of the walls, you can now mark the level lines on the walls. This will determine the location of the base cabinets. You can also mark the vertical level line on the wall. Once you’ve completed this step, you can attach the cabinets using wood screws through the drywall.
Shim the base cabinet top
You can shim the top of base cabinets to prevent the back of the cabinet from popping out. You should use shims that match the back corner of the cabinet. To shim the top of base cabinets, first level the wall using a leveling tool, and then slide the shims in from the bottom.
Once you’ve done this, place the next section of cabinet on top of the first section. Make sure that the cabinet is level from front to back. If there are gaps in the wall, use shims to fill them in. You can use a utility knife to score or snap the shims flush.
If the wall is high, use a leveler to mark the high point. You can use a level or laser level to mark the spot. If the cabinet is level, you don’t need shims. To get a level reading, place the leveler parallel to the wall where the front cabinet edge will rest. When the cabinet is level, the high point is the level of the wall and it’s a good reference mark. By following these steps, you can be sure that your cabinet top is level and the countertops are plumb.
Before installing base cabinets, you need to install corner cabinets first. You’ll need a helper for this step. Once you’ve installed the corner cabinet, make sure that the screws penetrate the wall studs by at least one inch. You should then back off the screws and tap shims at the location of the studs. Once everything is level, you can attach the remaining cabinets.
Place the end units 1/4 in. away from the layout line
Using a stud finder, locate studs behind the wall and screw the ledger board into the studs. Once you’ve installed the ledger board, install cleats at the end of each cabinet unit. These cleats support the unit from below.
When installing kitchen cabinets, you need to keep the layout line level all around. It is important to keep this level line so that the cabinets are installed evenly. Also, use a laser level to make sure you’re working with an accurate reference line.
Install the ledger board
Before installing your new cabinets, make sure you have the ledger board ready. You’ll need it to hold the cabinets while you are installing them. You can use a stud finder to do this. Next, mark the wall studs at the correct spot. Be sure to use a level to mark the studs. You should also mark the placement of the wall cabinets and appliances. After you’ve made the layout, you can install the ledger board.
To install the ledger board, first make sure the cabinet’s mounting point is level. Then, use a hand-held drill to attach it to the wall. Once the cabinet’s mounting points are leveled, you can mount the doors and hardware. You can also use the ledger board to secure the base cabinets to the wall.
After you have installed the ledger board, you can begin hanging the upper cabinets. You can also use a helper to hold the upper cabinets while you install the screws. You can also use a box to measure the upper cabinets before you install them. It will help keep the cabinets level and eliminate the frustration of holding them in place. Then, you can begin installing the bottom cabinets.
Install the filler strips
Once you’ve cut the filler strips to size, you can begin installing them. The process is the same as for the upper cabinets. First, set the upper cabinets on the cabinet jack. If necessary, use a scribing tool or a pencil to transfer the contour of the wall to the filler strip. Then, using a belt sander, shape the filler strip to fit snugly in the gap. The front edge of the strip should be sharp.
Once the filler strips are installed, you can screw them onto the cabinet frame. This step will require more tools, such as a drill bit that matches the screw shaft. You’ll also need a wooden block that’s the same thickness and length as the filler strip. And, if your cabinets are on upper shelves, you may need a step ladder to reach the top.
Before you install the filler strips, you’ll need to determine how wide you want the gaps to be. A good rule of thumb is to measure at least three inches from the top to bottom of the cabinet. If the gaps are uneven, you should cut one filler strip slightly wider than the other. Then, use an L-bracket to join the filler strips. When you’re done, use a 1 by two backer board to support the filler strip.
